In its most basic application, a SNOUT hood is installed over the outlet of a catch basin or other stormwater quality structure with a deep sump. The bottom of the hood extends well below the invert of the outlet pipe creating a separation layer on the surface.

BMP's catch basin baffles and drain traps keep stormwater systems effective. Learn about our innovative catch basin hoods and filters.

the SKUNK is a catch basin hood that stops trash from entering our rivers, lakes, and oceans the SKUNK provides a low-cost, retrofittable solution for capturing floatable trash and oil. Retrofittable into existing sump structures

Jul 15, 2022 · In its most basic application, a SNOUT hood is installed over the outlet pipe of a catch basin or other stormwater quality structure with a deep sump (Download Complete Installation Drawing). The SNOUT forms a baffle that traps floatable debris and free oils on the surface, while permitting heavier solids to sink to the bottom of the sump.

Two deep-sump catch basins were equipped with cast-iron hoods. Three were equipped with molded plastic hoods, known as an Eliminator, and a single catch basin was equipped with a fiberglass anti-siphoning hood, known as a Snout.

Catch-basin hoods are intended to enhance catch-basin performance by retaining floatable debris, including floatable oil, grease, and petroleum hydrocarbons, at the water surface within the sump of the catch basin. Catch basins that do not contain hoods have no physical means of retaining floatable solids in the catch basin sump.

ALL HOODS SHALL BE CONSTRUCTED OF A FIBERGLASS REINFORCED RESIN COMPOSITE WITH ISO GEL COAT EXTERIOR FINISH WITH A MINIMUM 0.125" LAMINATE THICKNESS. ALL HOODS SHALL BE EQUIPPED WITH A WATERTIGHT ACCESS PORT, A MOUNTING FLANGE, AND AN ANTI-SIPHON VENT PIPE AND ELBOW AS DRAWN. (SEE …

In its most basic application, a SNOUT hood is installed over the outlet pipe of a catch basin or other stormwater quality structure which incorporates a deep sump (see Installation Drawing).

Catch Basin Hoods and Traps www.generalfoundries.com salesgeneralfoundries.com 800 222 9555 CB-35 NOTES: - Dimensions are approximate & in inches - Conforms to ASTM A36 - Coating: Painted black or galvanized (please specify) PRODUCT NO. A B C PIPE OD FBT24 30 36 15 24 FBT30 36 42 20 30 Fabricated Steel Trap A B C SUPPORT BAR

Hoods and Traps are Used in Catch Basins to collect debris. They are used in many different municipalities as a debris shield before waste enters the waterways. New York City requires Hoods to use Stainless Steel hooks.

Two deep-sump catch basins were equipped with cast-iron hoods. Three were equipped with molded plastic hoods, known as an Eliminator, and a single catch basin was equipped with a fiberglass anti-siphoning hood, known as a Snout.

Mar 16, 2021 · The BMP Snout is a high-performance vented hood with more than 65,000 installations. This system reduces trash, floatables, oil and sediment from storm water discharges. Performance-boosting accessories include the Bio-Skirt, an antimicrobial treated hydrocarbon-reducing skirted boom; the stainless TrashScreen for full trash capture; and the ...

Use catch basin hoods that reduce or eliminate siphoning. Catch basins should be watertight to maintain a permanent pool of water and provide higher floatable capture efficiency.

Rollee's Aluminum self-locking trapping hood n ozzle type split collar allows for a "force fit" placement in drainage pipe, eliminating the need for pins or hooks in the wall of catch basin during install. Hinged rear gate allows for ease of cleaning as well as opening for flood relief.

BMP's storm drain outlet protection keeps your system clean. Contact us to learn about our gully traps and catch basin trapping hoods.

Deep sump hooded catch basins and can be impractical for use with surface stormwater BMPs due to the depth of the catch basin outlet pipe. Deep sumps catch basins are storm drain inlets that have a sump below the outlet pipe to capture trash, debris, and …

May 29, 2018 · More than 35,000 Snouts are helping communities comply with storm water quality regulations. The system reduces fl oatables, oil and sediment from storm water discharges. The Snout installs in a sumped catch basin or water quality structure. The Bio-Skirt reduces bacteria and increases oil removal.

Jun 22, 2021 · More than 65,000 BMP Snouts are cleaning up storm water runoff in North America. The system reduces trash, sediment, oils and other common pollutants from storm water discharge. CAD drawings and pricing are available online. The product is made in the U.S. Visit the company at StormCon booth #519.

In its most basic application, a SNOUT hood is installed over the outlet of a catch basin or other stormwater quality structure with a deep sump. The bottom of the hood extends well below the invert of the outlet pipe creating a separation layer on the surface.

Deep sump catch basins, also known as oil and grease or hooded catch basins, are underground retention systems designed to remove trash, debris, and coarse sediment from stormwater runoff, and serve as temporary spill containment devices for floatables such as oils and greases.